FM-1000 Support

Which frequency and baud rate do I need for central RTX beam?

Central USA Beam is 1557.8150Mhz with a baud rate of 2400.

What cables do I need to connect an FM1000 to a Pro 700?

ZTN67091 (port replicator) & ZTN59043 (null modem cable). ZTN67091 is a port replicator that will plug into the back of the FM 1000. From there, the ZTN59043 will plug into the 67091 and into the Pro 700. ZTN59043 is a null modem cable.

FM-1000 or FM-750 screen locks up during operation. What can I do?

Reboot the display. If the issue is not resolved, contact your dealer for further troubleshooting

I tend to operate during times of the day that have poor satellite coverage. How can I plan around this?

Trimble provides a satellite coverage planning tool at www.trimble.com/GNSSPlanningOnline. Locate your location on the map, and this tool will indicate the number of satellites visible during the selected timeframe.

Can I use my DCM-300 modem for VRS corrections on my FM-750 / FM-1000 / AFS 372 Receiver?

Yes, contact your dealer for details.

How do I know what features are unlocked in my display?

From the home screen of the FM1000, select the "Unlocks" option. This will populate a list of what is unlocked in the display. This applies to display features as well as correction levels.

Can I use AFS Connect for NTRIP on my Case IH vehicle that has a Trimble display?

Yes, AFS Connect can be used. An NTRIP subscription is required. Contact your dealer to purchase.

A cellular RTK subscription must be purchased separately.

NTRIP connectivity is achieved by entering the NTRIP server details using a Case IH AFS Pro 700 monitor. Once the modem is configured it will stay configured.

How can I determine the software version of the FM-1000?

Navigate to the System Information Tab from the home screen. The software version is located in the upper left.

How can I determine the Autopilot software version using an FM-1000?

Navigate to the System Information Tab from the home screen. The Autopilot Controller version is located on the right.

How can I determine the amount of internal memory remaining on my FM-1000 Display?

Navigate to the System Information tab from the home screen. The internal memory status is located in the lower left.

Which frequency and baud rate do I need to receive Centerpoint RTX corrections?

Satellite settings for CenterPoint RTX, RangePoint RTX, xFill, and Omnistar correction services are as follows:

Eastern North America Beam frequency is 1557.8590 with a baud rate of 600
Central North America Beam frequency is 1557.8150 with a baud rate of 2400
Western North America Beam frequency is 1557.8615 with a baud rate of 600

How do I email my .cn1/AgGPS folder to AFS Support?

1. Power the display OFF with the memory device installed.
2. Remove the memory device from the display.
3. Take the memory device from the display to a computer. If a window does not launch when the memory device is installed, then click the "Start" button on the Windows task bar and select "My computer" from the pop-up menu.
4. Select the drive that corresponds to the memory device drive location – for example, “Removable Disk (E:).”
5. Right click on the folder that ends with .cn1 to access a pop-up menu.
6. Click "Send To > Compressed (zipped) folder" or compress the folder with a third party application such as 7-zip or Winzip. Note the location of the .zip file for the next step.
7. If required, transfer the .zip file to a computer that has access to email.
8. Attach the .zip file to an email message.

What does the XCN-2050 display offer that my FM-1000 display does not?

Not only does the XCN-2050 display have a faster processor and larger internal memory, but new features such as NextSwath are only available for the XCN-2050. The XCN-2050 is designed to handle the increased demands of new applications and allow for future expansion.